Why Orbi RBR850 Shows a Constant Pink Light (and How to Fix It)

If your Orbi RBR850 has been sitting there with that weird constant pink (or magenta) light, you already know something’s off. Orbi pink light means that the router is have trouble connecting to the internet or syncing with the modem. Sometime this issue is for few minutes and sometimes it become constant problem of connection issue. Both ways, looking at Orbi pink light won’t help you. You need to fix it by yourself. A few quick checks can resolve the Orbi RBR850 constant pink light such as power, cables, firmware update, and factory reset. Let’s break down exactly why that pink light shows up and the real fixes that actually work.

Steps to Fix Orbi Pink Light on RBR850

1. Check the Internet Connection First

You need to start with the obvious one. Unplug the Orbi router and plug your computer directly into the modem using an Ethernet cable. Open any website. If that doesn’t load, your modem or your ISP is the one with the issue causing Orbi pink light. That means the Orbi’s not the problem, it’s just not getting a signal to work with. Restart the modem, wait a couple of minutes then plug the Orbi back in. Half of the time, this alone fixes the issue. The router just needed to catch a proper signal again. If it’s still pink after that, move on.

2. Make Sure the Cables Are Connected Properly

Most of the time people ignore this minor cause but it is way more common than people think. The Ethernet cable between the modem and the Orbi’s yellow Internet port needs to connect tightly. If it is loose then the router just assumes that there is no connection.

While you’re at it, you must also check the power adapter too. Sometimes, a half-plugged power cord drops the voltage and router starts acting up. Unplug both cables and plug them back in firmly. Wait for a minute and see if the pink light turns to white and then blue. If it does, you’re good. If not, keep digging.

3. Power Cycle Everything

You need to power cycle both your modem and Orbi RBR850. To do that, you need to unplug the modem first then the Orbi router. Wait for 2 to 3 minutes then plug the modem back in and let it boot completely, it can take a couple of minutes. Once the lights are solid on model, you need to plug the Orbi back in.

If it connects properly this time then you’ll see a solid blue light for a bit which is a good sign. If it goes back to pink, you need to dig deeper.

4. Update the Firmware

Out-dated firmware is one of the sneaky reasons behind these color codes. The RBR850 is powerful but like any smart router, its software can glitch out. Go to orbilogin.com on a device connected to the router. Log in to orbilogin using admin details, head to Advanced > Administration > Firmware Update and check for updates.

If there is new firmware update available, install it manually or automatically. After updating the firmware, reboot the Orbi and give it a minute to re-sync. This can clear up the Orbi pink light issue which is caused because of software bugs.

5. Check the Modem Type and Compatibility

If you are using a modem which your ISP gave you ages ago then that could be the problem. Some of those old gateway units don’t play nicely with mesh systems like the Orbi. You might need to put the modem in ‘bridge mode’, so the Orbi can handle all the routing duties. Go into the modem settings and see if your modem can be bridged. Once that is done, the Orbi gets a clean signal and usually syncs up instantly.

6. Try Relocating the Router

This one is rare but sometimes the Orbi just overheats or struggles with interference from other electronics. If it is sitting on top of your modem or right next to a big metal surface, move it somewhere with more breathing room. Give it space like a shelf or table where air can circulate.

It shouldn’t constantly show pink for this reason alone but it can make a difference if the router has been under strain for a while.

7. Factory Reset (When Nothing Else Works)

If you’ve tried all that and the pink light is still on then it is time for factory reset. It is the only way to clear the bad settings and corrupted configuration.

You need to use a paperclip to insert at the reset button on the back of the Orbi for about 10 seconds. Once it flashes the white light, it means your device is set to factory reset. After resetting the Orbi, you need to set it up again via Orbi app or orbilogin interface.

We hope that following these steps will resolve the Orbi pink light issue and get your WiFi running smooth again.

Conclusion

In short, we can say that constant pink light on the Orbi RBR850 isn’t the end of the world. It’s just your router throwing a little tantrum because it is unable to reach the internet or connect to the modem. Most of the time, the reason is something small like cable, reboot, or firmware acting up. Once you go through these above fixes and let it sync again then the Orbi pink light will turn back into blue light. Hopefully these steps save you the headache and get your WiFi back without needing to replace anything.